Similarly, if someone is trying to disarm your system by removing the power then it will start beeping and usually, burglars will get scared and leave your house. However, having a simple power cut can also cause similar problems. So, if you have the same issue, these steps might help you. How to Fix Alarm System Beeping After Power Outage?
Why is my ADT system beeping?
A complete power outage can result in the beeping. This beeping alerts you that the system is running on backup power. The beeping could be a result of the backup battery failing to maintain its charge properly. If this is the case, you may need to consult ADT to replace the battery.
Is my ADT alarm working when I lose power?
Is My ADT Alarm Working When I Lose Power? Your ADT alarm system comes with a backup battery. This battery will immediately activate in case of a power outage. It will keep your security functional for at least several hours once your power goes out.
How do I restart my ADT system after a power outage?
Once the system is powered up, go to your control panel. At this point, the system should be reset to its original state, and you should be able to arm or disarm it accordingly. Still having Trouble? You may still be unable to restart your ADT system after a power outage.
Great, you’ve been standing in a dark house for who knows how long, and now that the power is back, your ADT alarm won’t stop beeping. Before you pick up the phone and give ADT a piece of your mind, it only takes a few seconds for the beeping to stop.
Here’s how to fix your ADT alarm beeping after a power outage. We’ll also let you know what the beeping means and when you need to call in an expert.
Alarm’s Beeping VIEW ON AMAZON
How to Stop ADT Alarm’s Beeping
Your ADT Alarm keeps working even if your power goes out. That’s because it runs on a backup battery. However, if the battery is low, the alarm will beep, alerting you to change it.
You typically have two options for stopping the beeping:
- You can press the pound key.
- You can press the “off” button.
Remember: this is only a temporary fix. You’ll need to eventually change the batteries to get your system back on track.
If your system’s still beeping, your best bet is to change the batteries. The types of batteries you need depend on what type of alarm system you have. To change your ADT alarm’s batteries:
Put Your System into Test Mode
Before doing anything else, you should put your ADT Alarm in “Test Mode.” This notifies the system that you’re making changes and doesn’t send alerts to ADT. You can put your alarm into test mode using the app, but we recommend doing it from ADT’s website:
- Go to MyADT.com and enter your login information.
- Choose “My Alarm” from the dashboard.
- Click “System Management.”
- Click “Place alarm on test mode.”
If you have problems with these steps, watch this short video about putting your alarm in test mode via the app. Alternatively, you can call 888-ADT-ASAP to put your alarm in test mode. Be prepared to provide information about your ADT account and where you live.
Insert the New Batteries
Your ADT Alarm is a sensitive piece of technology. As such, the process isn’t as easy as pulling it off the wall and putting new batteries in. You’ll need to:
- Open your system’s front panel. You might need a key to do this. If so, it should be located on the panel’s top left-hand side. Disconnect the wires from the battery. You can do this by unraveling the wires around the nodes.
- Connect the red wire to the battery’s red tab.
- Connect the black wire to the battery’s black tab.
- Close the front panel.
Take Your Alarm Out of Test Mode
To take your alarm out of test mode via the website:
- Go to MyADT.com.
- Choose “My Alarm.”
- Go to “System Management.”
- Select “Stop Test.”
Taking your device out of test mode is not the same as arming your perimeter. You will need to enter your password to re-arm your system.
What if My ADT Alarm Is Still Beeping?
Consider how the following could address your situation:
Recheck the Battery’s Connection
It’s possible that you successfully replaced the battery itself, but energy isn’t flowing through the wires. Depending on your system, you may need to wrap the copper ends of the wires around the battery’s nodes.
On the other hand, make sure the new battery itself has a charge. You can do this by using a battery checker tester or using batteries straight from the packaging.
Reset Your System
Resetting a malfunctioning device is the “abracadabra” of the technology world. Nobody knows why this fixes so many errors, but it does. Try resetting your system if the beeping won’t stop. ADT provides these resources:
- User manual guides, which provide specific resetting instructions for your device
- Reset combinations that vary depending on what type of system you have
Cut off the Alarm’s Power
Your alarm can’t beep if it doesn’t have a power source. First, put your alarm into test mode using the information outlined above. Then:
- Locate your home’s fuse box.
- Shut off power to the wall/room your ADT Alarm panel is in.
- Remove the batteries from the device.
- Wait a few seconds.
- Put your alarm back online by replacing the batteries before turning the power back on.
The beeping should stop when it powers back on. Remember to take your alarm out of test mode beforehand.